Searched for "40141900"
Dundas Jafine's 4 in. aluminum tension clamps are ideal for use with flexible or semi-rigid ducts. These clamps open and close with pressure. No tool required.
- Ideal for use with flexible or semi-rigid ducts
- Aluminum construction
- No tools necessary
- Easy operation
Heavy Gauge 4 in. Pipe is used to vent boilers, furnaces and hot water heaters. Available in a variety of common lengths, diameters and gauges to help make your next HVAC project a success. A simple snap lock design and sturdy galvanized steel construction combine for a quick and secure installation that you can rely on.
- Easy-to-install snap lock design
- Crimped end with a stop-bead for a secure interlocking fit
- Sturdy 26-Gauge, galvanized steel construction
- Always seal seams with building code approved sealant or duct tape
- Always insulate ductwork for greater system efficiency and comfort
Heavy Gauge Adjustable Elbows are used to make angular turns in round pipe to vent boilers, furnaces and hot water heaters where allowed by code. They have a sturdy galvanized steel construction and are simple to adjust. They are also crimped on one end to easily fit into a pipe or other fitting of the same diameter.
- Used to make angular or gradual turns in runs of pipe
- Adjustable to any angle through 90 degree
- 28-Gauge, galvanized steel construction
- Crimped end for easy installation
- Always seal seams with building code approved sealant or duct tape
- Always insulate ductwork for greater system efficiency and comfort
Master Flow Drive Cleats and S Cleats are used to join sections of rectangular duct and stack duct in. HVAC systems. These cleats are sleeves of galvanize steel that help to securely assemble the top and bottom (S) and left and right sides (Drive) of rectangular duct runs. S cleats are used to connect the long side of the duct, while Drive cleats are used to connect the short side.
- Always seal seams with code approved mastic or sealant (or duct tape)
- Always insulate ductwork for greater system efficiency and comfort
- S cleats secure bare edges of rectangular duct
- Insulate ductwork to promote system efficiency
Duct strapping is ideal for use in hanging hot air supply and cold air returns to framing members. Founded in 1971, Diversitech Corporation is North Americas largest manufacturer of equipment pads and a leading manufacturer and supplier of components and related products for multiple industries, including: HVACR, electrical, consumer hardware retail, electrical utility, automotive retail and pool and spa channel. Diversitechs mission for its wholesaler partners is to simplify their work. We do this by offering more than 200 product categories all from a single manufacturing/supplier source to create product availability and supply chain cost advantages for our customers in every market we serve. We also leverage best-in-class customer service to react quickly and professionally to every customer request.
- Galvanized steel construction resists corrosion
- Solid strapping, easy to drill or nail
- Can accept fasteners at any point along the length of the strapping
- Convenient cardboard dispenser allows for easy transport
These Worm Clamps are ideal for attaching aluminum ducts to other aluminum products, including elbows and pipe. Easily adjustable with the turn of a screwdriver, these clamps can be used with all venting applications. A heavy-duty galvanized steel construction ensures longevity through a variety of uses. For optimal performance, it is recommended to use a manual screwdriver to avoid over tightening and stripping the screw.
- Made of heavy duty galvanized steel
- Easily adjustable using a hex or flat head screwdriver
- Adjusts from 5-1/8 in. to 6-1/2 in.
- Can be used in all venting applications
Master Flow standard 90 adjustable 7 in. elbow is used to make turns in runs of round pipe and flexible duct through 90. It has a sturdy galvanized steel construction and is simple to adjust. It is also crimped on 1 end to easily fit into a pipe or other fitting of the same diameter. Ships in 90 position.
- Used to make angular or gradual turns in runs of pipe
- Adjustable to any angle through 90 degree
- 30-Gauge, galvanized steel construction
- Always seal seams with building code approved sealant or duct tape (not included)
- Always insulate ductwork for greater system efficiency and comfort (not included)
Dundas Jafine's aluminum Elbows can be used to vent most types of heating units. This product features an all-aluminum, 4-piece construction and is fully adjustable to 90 degree . Includes one crimped end and one solid end to ease assembly.
- 0.016-Gauge aluminum
- Heavy-duty
- Fully adjustable to 90 degree
- 4-piece construction
Master Flow 26-Gauge 90Adjustable 3 in. Elbow is used to make turns in runs of round pipe and flexible duct through 90. It has a sturdy galvanized steel construction and is simple to adjust. It is also crimped on 1 end to easily fit into a pipe or other fitting of the same diameter. Ships in 90 position.
- Used to make angular or gradual turns in runs of pipe
- Adjustable to any angle through 90
- 26-Gauge, galvanized steel construction
- Always seal seams with building code approved sealant or duct tape (not included)
- Always insulate ductwork for greater system efficiency and comfort (not included)
The Master Flow 4 in. Round Duct Cap, also called a tee-cap or clean-out plug, is constructed of galvanized steel for durability. The duct cap is used to terminate or block off a rectangular duct run in HVAC systems. It can be installed with sheet metal screws (sold separately) and is suitable for most HVAC applications.
- Use to cap off a round or rectangular duct run
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
The Master Flow 6 in. Starting Collar is suitable for most HVAC applications. It provides a transition from a flat surface like a plenum (made from metal, ductboard or insulated) to round pipe or insulated flexible duct. It can be used with ductboard, an internally lined or unlined plenum. This galvanized steel starting collar features extra-long tabs to fit most duct board thicknesses.
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Can be used with an internally lined or unlined plenum
- Extra-long tabs to fit most ductboard thicknesses through 1-1/2 in. (or R-6 value)
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
The Master Flow 8 in. to 6 in. x 6 in. Wye is made of 30-Gauge, galvanized steel. It is designed to transition from 1 pipe to 2 pipes for heating and air conditioning applications. The wye is easily installed with sheet metal screws (not included). It has a maximum temperature rating of 390 degree F.
- Designed to transition from 1-pipe to 2-pipes in heating and air conditioning applications
- Easily installed with sheet metal screws (not included)
- Maximum temperature rating of 390 degrees Fahrenheit
- Always insulate ductwork for greater system efficiency and comfort
- Seal seams with code-approved mastic, sealant or duct tape (not included)
The Master Flow 8 in. Starting Collar is suitable for most HVAC applications. It provides a transition from a flat surface like a plenum (made from metal, ductboard or insulated) to round pipe or insulated flexible duct. It can be used with ductboard, an internally lined or unlined plenum. This galvanized steel starting collar features extra-long tabs to fit most duct board thicknesses.
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Can be used with an internally lined or unlined plenum
- Extra-long tabs to fit most ductboard thicknesses through 1-1/2 in. (or R-6 value)
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
The Master Flow 6 in. Round Duct Cap, also called a tee-cap or clean-out plug, is constructed of galvanized steel for durability. The duct cap is used to terminate or block off a rectangular duct run in HVAC systems. It can be installed with sheet metal screws (sold separately) and is suitable for most HVAC applications.
- Use to cap off a round or rectangular duct run
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
Master Flow Drive Cleats and S Cleats are used to join sections of rectangular duct and stack duct in. HVAC systems, these cleats are sleeves of galvanize steel that help to securely assemble the top and bottom (S) and left and right sides (Drive) of rectangular duct runs. S cleats are used to connect the long side of the duct, while Drive cleats are used to connect the short side.
- Always seal seams with code approved mastic or sealant (or duct tape)
- Always insulate ductwork for greater system efficiency and comfort
- Can be hammered in place
- Insulate ductwork to promote system efficiency
The Master Flow 26 Gauge 7 in. x 6 in. Flat Reducer is made OG galvanized steel. Its short length makes it ideal for tight spaces. The reducer is used to transition from a 7 in. pipe to a 6 in. pipe system. It is suitable for most HVAC applications.
- 26-Gauge, galvanized steel construction for durability
- Connects 7 in. pipe to 6 in. pipe in duct run
- Connect using sheet metal screws (not included)
- Universal - not crimped
- Can be crimped as needed
The Master Flow 4 in. Diameter Starting Collar is crimped for easy installation. This starting collar can be used to transition from a flat surface such as an unlined metal plenum to round metal pipe. Can also be attached to most unlined metal ductwork, such as rectangular duct. Constructed of galvanized steel, this starting collar is made for durability.
- Made of galvanized steel
- Fits most 4 in. metal pipe
- Helps transition from unlined metal duct to round pipe
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
The Master Flow Air-Tite 6 in. Take-Off provides an airtight seal when connecting insulated flexible duct or round pipe to a flat surface. This take-off can be used to redirect air from any side of the plenum or to transition from a rectangular pipe run. The built in damper allows adjusting air flow in the duct run. The Air-Tite Take-Off can be installed with sheet metal screws (sold separately) and is suitable for most HVAC applications.
- Built-in damper
- Can be used to route air from any side of the plenum or to transition from a rectangular pipe run
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Tacky gasket helps create a secure, airtight seal
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
Master Flow 26-Gauge 90 Adjustable 4 in. Elbow is used to make turns in runs of round pipe and flexible duct through 90. It has a sturdy galvanized steel construction and is simple to adjust. It is also crimped on 1 end to easily fit into a pipe or other fitting of the same diameter. Ships in 90 position.
- Used to make angular or gradual turns in runs of pipe
- Adjustable to any angle through 90
- 26-Gauge, galvanized steel construction
- Always seal seams with building code approved sealant or duct tape (not included)
- Always insulate ductwork for greater system efficiency and comfort (not included)
This 4 in. aluminum duct connector attaches 2-pieces of 4 in. flexible duct together. It is ideal for use as both a duct connector and extending the exhaust collar of your clothes dryer. Product length is 6 in.
- All aluminum construction
- Includes 1-straight end and 1-crimped end for ease of installation
- Can be used with all types of flexible ducts
- Can be used in both gas and electric dryer applications
Master Flow 26-Gauge 90 Adjustable 8 in. Elbow is used to make turns in runs of round pipe and flexible duct through 90. It has a sturdy galvanized steel construction and is simple to adjust. It is also crimped on 1 end to easily fit into a pipe or other fitting of the same diameter. Ships in 90 position.
- Used to make angular or gradual turns in runs of pipe
- Adjustable to any angle through 90
- 26-Gauge, galvanized steel construction
- Always seal seams with building code approved sealant or duct tape (not included)
- Always insulate ductwork for greater system efficiency and comfort (not included)
The Master Flow 6 in. Starting Collar is suitable for most HVAC applications. It provides a transition from a flat surface like a plenum (made from metal or lined duct) to round pipe or insulated flexible duct. A Damper can be added to this model if needed.
- Connects round pipe or insulated flexible duct to a flat surface to start a duct run
- Fits most HVAC types for universal application
- Can be used with an internally lined or unlined plenum
- Extra-long tabs to fit most duct board thicknesses through 1-1/2 in. (or R-6 value)
The Master Flow 8 in. Round Duct Cap, also called a tee-cap or clean-out plug, is constructed of galvanized steel for durability. The duct cap is used to terminate or block off a round duct run in HVAC systems. It can be installed with sheet metal screws (sold separately) and is suitable for most HVAC applications.
- Use to cap off a round duct run
- Install with sheet metal screws (not included)
- Fits most HVAC types for universal application
- Seal seams with code-approved mastic, sealant or duct tape (sold separately)
This Master Flow 10 in. x 4 in. to 6 in. Universal Register Box creates a straight (in-line) transition from round pipe or insulated flexible duct to an air register or grille. It can be installed with sheet metal screws. It is suitable for most HVAC applications. This universal register box is made of galvanized steel.
- Creates a straight, in-line transition from an insulated flexible duct or round pipe to an air register or grille
- Installs with sheet-metal screws
- Insulate ductwork for system efficiency and comfort
- Seal seams with code-approved mastic, sealant or duct tape (not included)