Gas Ignition Controls
The Robertshaw 1980 Series Snap-Fit Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures. Various lengths are available.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Robertshaw 1980 Series Snap-Fit Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures. Various lengths are available.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Robertshaw 1980 Series Snap-Fit Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures. Various lengths are available.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Robertshaw 1980 Series Snap-Fit Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures. Various lengths are available.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Emerson 750 millivolt power generator is a replacement for similar screw-in type generators or for use with type E31-12 pilot burners. This generator is for 750 millivolt self-generation control systems. The PG9 adapter is also included in the box.
- 36 in. armored cable leads with split spade terminals
- PG9 adapter and clips included
- Mounting nut, spring clips and PG9 adapter sleeve included
- For use with type E1-12 pilot burner
The 1820 Series Uni-Kits are designed to replace those hard-to-find ITT General PG9 type pilots. Each Uni-Kit comes with a natural gas orifice installed and a separate L.P. gas orifice. A special 1/4" tubing adaptor is provided that allows use of original tubing with nut and ball sleeve. (No cutting of original tubing is necessary).
- Many flame pattern types available
- Thermocouple or thermopile options
- Spark electrode available
- Horizontal or vertical gas inlet
- Several mounting bracket types available
- Aerated pilots with non-linting characteristics
The 1830 Series Pilot Uni-Kit is designed to be used with all Uni-Line and competitive thermocouples. Kits include an adaptor that converts a threaded thermocouple/thermopile model 2CH to a snap-in thermocouple type, model 2C. Each kit comes with a natural gas orifice installed, and a separate L.P. gas orifice. Pilot tubing size is 1/4 in. tubing. These 1830-Pilot Uni-Kits are aerated type pilots, combining the best feature of an incinerator type pilot and a target type pilot. These pilots have non-linting characteristics, and no air shutters or supplementary shields requiring assembly or adjustment are needed.
- Many flame pattern types available
- Thermocouple or thermopile options
- Spark electrode available
- Horizontal or vertical gas inlet
- Several mounting bracket types available
- Aerated pilots with non-linting characteristics
The Robertshaw 1950 and 1951 Series Thermopiles lead the industry for gas appliance applications. Their primary function is to ensure a standing pilot light is operative so that on a call for heat, the main burner gas will be properly ignited. Thermopiles are placed in gas applications to detect the existence of a flame for safety purposes by shutting off the potential gas flow to a burner. A thermopile is the assembly of many thermocouples to increase the millivolt output. Robertshaw thermopiles have two types of connections: coaxial and two-wire spade connectors. The 1950 Series Thermopiles, also known as TP-75, are two-wire spade connectors. The 1951 Series Thermopiles, also known as CP-2 (250 to 750 millivolts), are coaxial connectors. The 1950 and 1951 Series Thermopiles (pilot generators) are designed for use on self-powered gas control systems. They can be used to replace similar competitive devices. It includes PG9 Pilot Adaptor.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-Gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC. some modules are rated for 208-Volt/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Robertshaw Carbide Series Hot SurfAce Ignitors deliver dependable ignition in heating systems. The applications include: furnAces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide. (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in plAce for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC, some modules are rated for 208/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide (Crystar) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-Gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC some modules are rated for 208-Volt/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Emerson Hot Rod premium nitride ignitor upgrades silicon carbide integrated or non-integrated systems to long-lasting and durable nitride. The nitride ignitor is connected in the existing HIS (hot surface ignition) system, ensuring consistent performance and long ignitor life. The 21D64-2 kit includes everything needed for a quick installation.
- Nitride Ignitor with 15.5 in. leads - replaces over 150 OEM, White-Rodgers and competitive HIS ignitors
- For gas-fired forced-air furnaces, water heaters and boilers
- Universal breakaway bracket included for easy installation and eliminating the need for multiple brackets
- What's in the box: Nitride Ignitor with 15.5 in. leads, universal mounting bracket, screw mounting adaptor, 2 ceramic wire nuts, furnace labels, instruction booklet
- 5-year warranty
The Robertshaw 1980 Series Snap-Fit Thermocouples offer easy installation into the majority of pilot burners. They are manufactured without complicated adaptors, but with extra insulation that the brass sheath provides under high ambient temperatures. Various lengths are available.
- Easy burner installation with attached threaded nut
- Stainless steel outer jacket for long life and resistance to heat blistering
- Combination of copper and nickel alloys for good electrical conductivity
- Mica washer to insulate from shorting conditions
- Tinnerman clip included
- Various lengths available for multiple applications
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide. (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC, some modules are rated for 208/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide (Crystar) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-Gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC some modules are rated for 208-Volt/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Robertshaw Carbide Series Hot SurfAce Ignitors deliver dependable ignition in heating systems. The applications include: furnAces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide. (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in plAce for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC, some modules are rated for 208/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Q3200U Universal Hot Surface Igniter Kit is designed to provide a robust field service replacement igniter, in gas fired appliances with Norton / St. Gobain / CoorsTek 120 Vac, silicon carbide, hot surface igniters. Pack of 6 igniters. Replaces over 110 OEM igniter models.
- Each igniter package includes cross reference instructions, six brackets, and installation accessories
- Robust Silicon nitride igniter construction
- Igniter application templates enable quick bracket selection
- Remote flame sense appliance applications only
Photoconductive Flame Sensor For Sequencing Oil Burner Systems, Shuts Down Protector lay When Flame Goes Out, 60 in. Leads. Includes Mounting Bracket, Use with Protector lay. On flame failure, the light sensitive cadmium sulfide cell, in conjunction with flame sensing circuitry, causes the Protector lay control to shut down the main oil burner. Glass-to-metal hermetic seal in plug-in cell prevents deterioration by humidity, soot or oil fumes.
- Includes A, B, C, J and P mounting brackets and fuel line adaptor
- Lead wires: NEC class 1, includes 2 flag 1/4 in. quick connects
- Type R bracket
- 120320 replacement cad cell, 7.5 mA minimum sensitivity at 2 ft. candles, 130367 replacement cad cell, 12.0 mA minimum sensitivity at 2 ft. candles
This ignitor flame rod assembly is designed for Smart valve pilots. It can be used with the Q313 thermopile generator. This assembly is designed for 750 mV power pile applications.
- Variety of mounting brackets available
- Variety of tip styles provides desired flame pattern
- Interchangeable, color-coded orifice and inlet fittings available
- Convert between natural and LP gas
Universal intermittent pilot ignition module replaces multiple field installed intermittent pilot modules supplied by Honeywell, Robertshaw, Johnson and UTEC (HSC). Uses existing intermittent pilot burner. Includes cross reference, instructions and accessories for easy replacement.
- Replaces over 400-white-rogers, robertshaw and honeywell intermittent pilot ignition modules
- Provides ignition sequencing, flame monitoring and safety shutoff for intermittent pilot warm air furnaces and heating appliances
- Provides 100% pilot gas shutoff if pilot fails to light; after 6-minute delay, trial for ignition is repeated, ignition trial/delay sequence is repeated until the appliance lights or call for heat is removed
- For use with natural or LP gas
The Emerson 768A series 80-Volt hot surface nitride ignitors feature teflon coated leads. This ignitor should be used with hot surface ignition for residential furnaces (Silicon Nitride replacement only). This ignitor has a 2-terminal AMP receptacle with 0.084 female sockets.
- Teflon coated leads
- 2 terminal AMP receptacle, 0.084 female sockets
- Replaces Lennox 41K5601, 768A-4 and Rheem 62-24134-02
- 2-terminal amp receptacle with 0.084 in. female socket
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide (Crystar) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC some modules are rated for 208-Volt/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The Robertshaw Carbide Series Hot Surface Ignitors deliver dependable ignition in heating systems. The applications include: furnaces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide. (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in place for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120V AC. Some modules are rated for 208/240V input, however, the voltage to the ignitor is stepped down to 120V AC
The Emerson 50A55-843 universal silicon carbide integrated hot surfAce ignition replAcement control kit. This ignition module replAces most Trane, York, ICP, Amana and White-Rodgers models. This module offers easy installation with the mounting plate (included in the box).
- Flash code diagnostics for easy service
- Fused to protect low voltage system transformers
- Includes mounting template
- Adjustable blower delay
- Pre-purge 30-seconds
- Delay heat on 30/45
- Delay heat off 60/90//120/180
- Delay cool on 5
- Delay cool off 45/90
- Input voltage 25 VAC 50/60 Hz
Mr. Heater Original Tank Top replacement thermocouple for original series models MH12-and MH24-. Copper construction and milled brass fittings. Prevents unburned propane releasing.
- Replacement for original series Mr. Heater tank tops models: MH12, MH12C, MH12T, MH12CS, MH12TS, MH24T, MH24TS, MH42T
- Copper construction
- Milled brass fittings
- Prevents unburned propane release
The Robertshaw Flame Sensor Assembly and Replacement Sensors have high temperature Kanthol sensor rods that will withstand 1800F (982C). The sensor rod is 4 long and can be cut and bent to match an original unit. Excellent replacement for most manufacturers' flame sensors.
- Includes 30 of Teflon insulated lead wire with a 482 degree F (250 degree C) rating
- Connects to a 1/4 in. quick connect terminal
- Replacement for most OEM flame sensors
- 4 in. sensor rod that can be cut and bent to match an original unit
The Robertshaw Carbide Series Hot SurfAce Ignitors deliver dependable ignition in heating systems. The applications include: furnAces, boilers, rooftop heaters, infrared burners, unit heaters, and water heaters. They can also be used in many other types of HVAC equipment.
- Made from high-purity recrystallized silicon carbide. (CrystarTM) which combines physical and thermal strength with stable electrical properties
- Designed to reach ignition temperature(s) within 17 seconds
- Have 18-gauge nickel chrome lead wires embedded and metalized in plAce for maximum holding strength and electrical conductivity
- Manufactured with lead wires enclosed in a special high-temperature fiberglass insulation providing electrical protection
- Operate at 120-Volt AC, some modules are rated for 208/240-Volt input, however, the voltage to the ignitor is stepped down to 120-Volt AC
The 1830 Series Pilot Uni-Kit models are designed to be used with all Robertshaw and most competitive thermocouples. Uni-Kit models include an adaptor that converts a threaded thermocouple/thermopile model 2CH to a snap-in thermocouple type, model 2C. There are many flame patterns available.
- Many flame pattern types available
- Thermocouple or thermopile options
- Spark electrode available
- Horizontal or vertical gas inlet
- Several mounting bracket types available
- Aerated pilots with non-linting characteristics
Universal hot surface ignition module replaces multiple field installed hot surface ignition. Uses a 120 VAC igniter. Includes cross reference, instructions, and accessories for easy replacement.
- Replaces over 800 White-Rodgers, Robert Shaw and Honeywell hot surface ignition models
- For 120 VAC (up to 5.0 Amp) surface igniter (Norton 201/271 or equivalent)
- S8910U 3000 series has LED status indicator and micro ammeter ports for easy trouble shooting
- For local (single rod) or remote (dual rod) rectification type flame sensing
Universal Integrated Furnace Control offers universal compatibility and diagnostics. It replaces a large number of furnace control models in single-stage warm air furnaces. Uses 120-Volt AC hot surface igniter. Includes instructions and special wire harnesses for easy replacement.
- Cross reference and wire harnesses provided for simple replacement over 195 existing furnace controls
- Main burner ignition using a 120-Volt hot surface igniter
- Flame rectification circuit to monitor flame presence
- Monitoring of system pressure switch, high temperature limit and rollout functions
Innovative technology is ever-present in our controls. Shop products that offer dependability, quality and customizable features. Only the best components to get the job done the right way the first time.
- Flame sensor for hot surface ignition (H.S.I.) systems
- Can be mounted remotely on multiple burners or adjacent to igniter on other applications
- For use with spark ignition and flame sensing
- High quality alumina ceramic insulator
- High temperature kanthal flame rod material that can withstand 1800F
- Instant heating technology saves time ensuring that hot water is always ready whenever you want
Goodman Direct Replacement Integrated Furnace Control Single Stage Hot Surface Ignition for 120V Ignitors. Replaces Goodman 0130F00005, 0130F00005S, B1809926, B1809926S, PCBBF110, PCBBF110S, PCBBF112, PCBBF112S, PCBBF123, PCBBF123S, White-Rodgers 50T55-289, 50A55-289. Diagnostic LED indicators streamline installation.
- Direct OEM replacement designed for high volume major brand controls
- Diagnostic LED indicators streamline installation and system troubleshooting
- 120-Volt air cleaner output and 120-Volt humidifier output up to 1 Amp maximum
- Factory standard safety timings and adjustable fan delay options
- Replaceable automotive style fuse
Innovative technology is ever-present in our controls. Shop products that offer dependability, quality and customizable features. Only the best components to get the job done the right way the first time.
- Flame sensor for hot surface ignition (H.S.I.) systems
- Can be mounted remotely on multiple burners or adjacent to igniter on other applications
- For use with spark ignition and flame sensing
- High quality alumina ceramic insulator
- High temperature kanthal flame rod material that can withstand 1800F
Direct Replacement 2-in-1 Air Handler control for Carrier Single Stage Air Handler with PSC Blowers. Replaces Carrier HK61EA002 and HK61EA006. Direct Replacement Makes Install Quick and Easy.
- Fast drop-in OEM mounting and wiring
- Factory wiring for inline connector or spade terminals
- Dipswitch selectable blower off delay
- Replaces carrier HK61EA002 and HK61EA006
Innovative technology is ever-present in our controls. Shop products that offer dependability, quality and customizable features. Only the best components to get the job done the right way the first time.
- Flame sensor for Hot Surface Ignition (H.S.I.) systems
- Can be mounted remotely on multiple burners or adjacent to igniter on other applications
- For use with spark ignition and flame sensing
- High quality alumina ceramic insulator
- High temperature kanthal flame rod material that can withstand 1800 degree F
The Emerson 50E47-843 universal silicon carbide non-integrated hot surface ignition module replacement kit. This ignition module replaces most White-Rodgers 50E47 and most competitive modules. This module offers easy installation with the double-sided foam black tape (included in the box).
- Program keys for multiple timings
- Flash code diagnostics for easy service
- Direct and indirect flame sense compatible
- Includes double sided foam black tape for easy installation
York Direct Replacement Integrated Furnace Control Single Stage Hot Surface Ignition. For 120V Ignitors. Replaces York , 265901, 265902, 539617, S1-03100662000, S1-03101250000, S1-03101266000, S1-03101267000, S1-03101267001, S1-03101284000, S1-03101933000,S1-03101972000, S1-03101973000, S1-03109167000, S1-33102956000, S1-33103010000, White-Rodgers 50A56-242, 50A56-243.
- Direct OEM replacement designed for high volume major brand controls
- Diagnostic LED indicators streamline installation and system troubleshooting
- 120-Volt air cleaner output and 120-Volt humidifier output up to 1 Amp maximum
- Factory standard safety timings and adjustable fan delay options
- Replaceable automotive style fuse
Universal Integrated Furnace Control Two-Stage Hot Surface Ignition for 3-Speed (ECM Blower Motor Systems). Includes 21D64-2 Universal Silicon Nitride Ignitor Upgrade Kit. Replaces White-Rodgers 50V51-xxx and 50V61-xxx 2-Stage HSI Systems with 80-Volt or 120-Volt Ignitors
- Reduces inventory by providing maximum control replacement coverage
- Includes a universal 120V nitride ignitor to allow replacement of 80V and 120V controls
- Diagnostic LED indicators streamline installation and system troubleshooting
- 120V air cleaner output and 120V humidifier output up to 1 Amp max
- Factory standard safety timings and adjustable fan delay options
- Replaceable automotive style fuse
Innovative technology is ever-present in our controls. Shop products that offer dependability, quality and customizable features. Only the best components to get the job done the right way the first time.
- Flame sensor for hot surface ignition (H.S.I.) systems
- Can be mounted remotely on multiple burners or adjacent to igniter on other applications
- For use with spark ignition and flame sensing
- High quality alumina ceramic insulator
- High temperature kanthal flame rod material that can withstand 1800 degree F
Universal Integrated Furnace Control Hot Surface Ignition. Includes 21D64-2 Universal Silicon Nitride Ignitor Upgrade Kit. Replaces over 200 OEM & Competitive Ignition Modules Including Carrier, Goodman, Trane, York and S9200U, Kit Replaces over 300 Models and Includes Wire Harnesses K & L to Replace Carrier Controls: HK42FZ004, HK42FZ007, HK42FZ008, HK42FZ009, HK42FZ011 or HK42FZ016.
- Replaces over 200 OEM and competitive single stage ignition modules to make repair quick and easy
- Comes with long lasting universal ignitor which will prevent future breakdowns
- Can be used in 120-Volt silicon carbide and 80-Volt silicon nitride ignition applications
- Fast install kit includes everything you need for quick and accurate replacement
- LED diagnostics for quick troubleshooting
- Fenwall Ignition Control for use with Magic-Pak HWC182, HWC242 and HWC302 Model Units
The Robertshaw 712 Series Intermittent Pilot Ignition System Kit features flame rectification with solid-state logic and flame sensing to provide automatic sequencing that will ensure proper operation of an intermittent pilot ignition device. The 712 pilot ignition systems are available with one of four different gas valve types to fit a wide range of furnace applications. Caution: Do not use on LP gas applications.
- Quick and easy installation
- Complete in-depth instructions and troubleshooting information
- Used on natural gas systems only
- Available with one of four different gas valve types to fit a wide range of furnace applications
