Searched for "40140000"
Engineered for reliability, The Taco Heat Motor Power Head provides a time proven method for operation of hydronic zone valves. The exclusive heat motor design operates silently, while the twist off head allows for serviceability without disturbing system connections. This power head is 24 VAC powered with an isolated end switch.
- Isolated end switch
- 24 VAC powered
- For Taco series 570 zone valves (570, 571, 572, and 573)
- Allows for service of valve without removing it
The 005-050RP Cartridge Assembly is used on several models of Taco circulators. This kit takes the place of conventional seal kits and is extremely easy to install. The Cartridge comes with all the hardware needed to extend your Taco Circulator's operating life.
- Repair part
- Includes casing body bolts
- Easy to install
- 3-year warranty
3-5/32" Centers
- Fits B&G Series 100B,PRAB,NBF-22,NBF-12,NBF-36,PL-36B,PL-55B and Armstrong Astro 30 and S-25 Pumps
- High-quality bronze body enables long-term use
- Features 150 maximum PSI
- Comes with 2 flanges
- Works well with Armstrong Astro 30 and S-25 pumps, Bell & Gossett series 100B, PRAB, NBF-22, NBF-12, NBF-36, PL-36B, and PL-55B models
This 1/2 in. lead free anti-siphon hot or cold water vacuum breaker prevents the reverse flow of polluted water from entering into the potable water supply due to back siphonage. It consists of polished chrome plated lead free construction, chemical resistant silicone seat disc, chrome hood, and an atmospheric vent to prevent spilling. It has a full size orifice to assure pipe size capacity and maximum flow. It is ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment.
- Lead free construction
- Chrome finish
- Female NPT inlet and outlet
- Hot or cold water
- Designed to prevent the backflow of polluted water from entering into the potable water supply
- Ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment
- Maximum pressure is 125 psi
Cast Iron Construction
- Couples Motor To Pump Inside Bearing Assembly Housing
- Fits B&G Series HV Pumps & Armstrong #H-32
SuperVent, purges air through a no clog vent assembly, to control dirt and debris and minimize air vent fouling in Hydronic heating systems, while eliminating the need for bleeding. Used in Residential or Commercial closed loop hydronic heating or chilled water systems. Can be cleaned in place.
- Stainless steel concentrator which eliminates gurgling noise
- Bronze body for rigid construction
- No clog vent
- Dirt and debris resistant
- Sweat connections
- 1/2 in. connection size
- Operating temperature range (F)240 degree F maximum
- 22 Cv capacity
- Maximum safe operating pressure 125 psi
- Rugged design stands up to tough conditions and continuous service
The Taco 1 in. cast iron Freedom Flange set includes: (2) flanges, (4) nuts, and (4) mounting bolts. These flanges are designed for use with Taco "00", "00e", "2400", and "100" series hydronic circulators. Easily installed and removed with a common wrench.
- For use in a heating system
- Compatible with a wide variety of Taco circulators
- 1 in. Dia connection size
- Unique hex design provides easy-on, easy-off installation with a standard adjustable wrench
The DELAVAN 1.00 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.00 60B1 Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
High Capacity Thermostatic Radiator Valves with T104 Actuators provide control of temperature by modulating the flow of hot water or steam through free-standing radiators, convectors and other heating units with high capacity requirements. Continually monitor and adjust room temperature for consistent comfort and relief from under-heating and overheating. Designed with the higher capacity normally required by North American heating systems.
- Controller with combined remote setpoint and sensor mounted on a wall. Setpoint/sensor connect with a capillary tube to an actuator, which mounts on the valve body. For V110 valves
- Valve seat disc, which is made of resilient material (EPDM), ensures tight shutoff on steam or hot water systems
- Nickel-plated bronze casted body with working parts in cartridge insert for ease of service
- All working parts are replaceable while valve remains in service, in-line, under pressure
- Controls include sensor, set point dial and valve actuator; components may be integral or connected by capillary tubes
- Require no electrical connections
- Meet ASHRAE standard 102-1989
- 40 mm collar diameter
- Temperature Range (F) 48 degree F to 79 degree F
- Capillary Length (ft)6 ft. 8 in.
All the features you trust from the original Isolator Uni-Flange ball valve, plus a 360 degree rotating flange that allows for orientation to any degree necessary for your installation. This forged brass full port ball valve features a blow-out proof stem, adjustable packing glands and a stainless steel snap ring for extra stability during installation. The only way to isolate circulator pumps.
- Conical inlet to minimize turbulence
- Replaces 3-components, eliminates 2-leak paths, saves approximately 20 minutes in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents electrolysis
- Eliminates galvanic corrosion
The Isolator is a uni-flange ball valve that isolates a circulator pump, allowing virtually no air into the system during pump replacement or service. Its innovative design combines multiple components into a single forged brass body that saves time, labor and space. The Isolator has revolutionized the installation of circulator pumps and has evolved into the largest flanged ball valve program in the industry today, featuring patented technology with further patents pending. Designed for use with water, oil, glycol mix in residential or commercial residential plumbing, commercial plumbing, heating systems. Refer to specification sheets for additional technical information. All Webstone products are backed by a limited lifetime warranty.
- Easily Isolates the Pump for Replacement
- Replaces 8 components, eliminates 7 leak paths, saves approximately one hour in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents Electrolysis and Eliminates Galvanic Corrosion
- Rotating Flange is Secured by a Snug-Fit Snap-Ring that Provides Greater Control Over Positioning During Installation
The DELAVAN 0.50 60A1 Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.00 70B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.85 60A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.10 70B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
This non-potable water expansion tank is designed for use in commercial and residential closed loop hydronic heating system piping to control the thermal expansion of hot water and maintain system pressure below the relief setting of the relief valve. This carbon steel tank is pre-charged at 12 PSI, tank volume is 2.1 gallons and features a durable expansion membrane that prevents contact of the water with the air in the tank. This rugged butyl diaphragm minimizes loss of the air change and ensures long and trouble-free life for the system. This tank is made of carbon steel with epoxy finish, mounts to supply piping, 1/2 inch MNPT system connection and a 0.302-32 inch charging valve connection (standard tire valve) to facilitate on-site charging of the tank to meet system requirements. The maximum working pressure is 75 PSI (5.3 BAR).
- Precharged to 12 psi
- Rugged flexible butyl diaphragm
- Inline and free standing models
- Steel construction
The Armstrong SBA contain an interchangeable module that includes a stainless steel pump shaft a housing that contains a precision crafted front and back end bearings that are permanentlty lubricated. Safer solutions for Facility and service personnel. faster onsite service and replacement.
- S&H #2 Series Maintenance-free Seal Bearing Assembly with Impeller
- Universal- fits B&G 3 piece circs
- A longer circulator life without maintenance (regular oil lubrication is not required)no more oil pools on floor
- Stainless steel face plate, coupler face guard meets or exceeds OSHA standards
- The standard for 65 years in hydronics
- Repairable, replaceable, environmentally friendly and now maintenance free
The DELAVAN 0.85 70W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.50 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.10 80A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
