Searched for "39131700"
The Electrical Box Extender lends support to the contents of a wall box. This non-conductive extender helps prevent arcing by forming a barrier between the box and the metal screws on the device. This box extender has a 2-hour fire rating.
- Levels and supports wiring devices in an electrical box
- Helps prevent arcing by forming a barrier between a metal box and metal side screws on the device
- Heavy-duty, non-conductive plastic construction
- UL and CSA safety listings
- Complies with 2008 NEC Article 314.20
Arlington's NM940-100 is listed for use with 1 or 2 cables. The Arlington Industries Inc. black Push-in Connector is easy and fast to install. The NM940-10 is a competitively priced Arlington item.
- Arlington's black button holds wires securely and exceeds UL pullout tests
- NM940-100 material is plastic construction
- Item is the lowest cost NM cable connector available today
- NM940-100 is simple to remove with a twist of a screwdriver
The 3/4 in. Twin-Screw Clamp Connectors (5-Pack) are designed to connect non-metallic sheathed cable and flexible cord to a steel outlet box or other metal enclosure. They are ideal for service entrances or other indoor applications. This clamp connector meets UL and CSA requirements.
- Connect non-metallic sheathed cable and flexible cord to a steel outlet box or other metal enclosure
- Corrosion-resistant zinc diecast construction
- Reversible locknut is designed to cut through protective coatings to assure ground connectivity
- UL and CSA Listed
- Tri-drive screw design works with all screwdrivers
- Locknut is reversible, it is designed to cut through protective coatings on boxes and enclosures to assure ground continuity
- Corrosion resistant
The 1/2 in. EMT Set Screw Connectors (5-Pack) are designed to connect and effectively bond EMT conduit to steel outlet boxes, load centers and other metal enclosures. Their bodies and locknuts are made with die-cast zinc alloy for strength and their set screws are made from zinc-plated steel. Their set screws' Tri-Drive head design works with Phillips, slotted and square screwdrivers.
- Connect and effectively bond EMT conduit to steel outlet boxes, load centers and other metal enclosures
- May be used indoors and in concrete-tight applications when taped
- Body and locknut made with die-cast zinc alloy
- Set screw made with zinc-plated steel
- Tri-drive screw head design for use with Phillips, slotted and square screwdrivers
- Screw thread is designed to not vibrate loose
- Reversible locknut designed to cut through protective coatings on boxes and enclosures
- CSA and UL Listed for safety
Install cable with these 3/4 in. Plastic Push-In Button Connectors (25-Pack). They are designed to fit up to 2 cables at once and accept cables without resistance for a smooth installation. Simple to remove with a twist of a screwdriver.
- Made of plastic
- Listed for up to 2 cables
- UL and CSA listed
- Snaps into knockout with light finger pressure
- Cables insert easily for smooth installation
The 2 in. Conduit Locknuts (2-Pack) are designed to secure rigid and IMC conduit or various threaded fittings to steel outlet boxes or other metal enclosures. They provide a grounded connection and are suitable for indoor applications. Designed to cut through protective coatings on boxes and enclosures to assure ground continuity.
- Secure rigid and IMC conduit or threaded fittings to metal electrical enclosures
- Made of galvanized steel
- Exceed UL 514B requirements
- Cut through protective coatings on boxes to assure ground continuity
Secure EMT conduit to wood and masonry work with this 1/2 in. EMT 1-Hole Straps (100-Pack). The steel straps are electro-plated in zinc for a corrosion-resistant design that is usable for both interior and exterior applications. These straps are UL and CSA Listed.
- Secures EMT conduit to wood, masonry or similar surfaces where load bearing is required
- Steel electroplated in zinc for corrosion resistance
- UL and CSA Listed
- Positively snaps on conduit when installed
- Usable indoors and outdoors
The 1-1/4 in. Conduit Locknuts (2-Pack) are designed to secure rigid and IMC conduit or various threaded fittings to steel outlet boxes or other metal enclosures. The zinc-plated locknuts are corrosion resistant. They provide a grounded connection.
- Made for connecting rigid and IMC conduit or threaded fittings to steel electrical enclosures
- Cast from corrosion-resistant galvanized steel
- For indoor or outdoor use
- Exceed UL 514B requirements
- Designed to cut through protective coatings on boxes to assure ground continuity
The 1-1/4 in. Plastic Insulated Bushing is designed to protect wires in threaded rigid or IMC conduits. It is made of heat-tolerant thermoplastic and can be used in indoor or outdoor environments. This bushing meets UL and CSA requirements.
- Protects wires in threaded rigid or IMC conduits
- Made of high-impact thermoplastic to withstand high-temperature environments
- Can be used indoors or outdoors
- UL and CSA Listed
Turn to the 1-1/4 in. EMT Compression Connectors (3-Pack) to join lengths of EMT to steel outlet boxes, load centers or other metal enclosures. Install these galvanized connectors either indoors or in concrete-tight applications. The connectors meet UL and CSA requirements.
- Connects EMT conduit to a steel outlet box, load center or other metal enclosure
- Galvanized steel resists corrosion
- CSA and UL safety listings
- For use indoors or in concrete-tight applications when taped
Knock-Out Seals are designed to cover exposed knock-out holes in steel boxes and other metal enclosures. The 1/2 in. Knock-Out Seals (4-Pack) offer corrosion resistance. They are convenient and easy to use.
- Covers knock-out holes in metal enclosures
- Zinc-plated steel
- Corrosion resistant
- Designed for indoor and outdoor use
Wiremold small surface metal raceway systems are the ideal choice for a homeowner that wants to extend circuits or communication cabling in their home. Surface metal raceway allows you to extend circuits, add fixtures or outlets without disturbing the drywall, plaster or insulation in your home. All parts are paintable to blend with room decor. The leading choice of professionals is now available for your DIY project.
- Shallow outlet box is used for most switches and receptacles when extending an electrical circuit from an existing switch or receptacle
- Base has two 1/2 in. trade sized knockouts
- Ivory finish
- Paintable using oil based products
- UL listed
The 3 in. Schedule 40 Non-Metallic 90 degree Elbow has a belled end and a standard bend radius. This item is designed for both above and below ground applications. This item is also UL and ETL Listed for safety.
- Enables a 90 degree change of directions in a run of conduit
- Belled end allows for easy joining of conduit
- Compatible with Sch. 40 rigid non-metallic conduit
- Resists rust and corrosion
- Listed for exposed and outdoor usage
- UL and ETL Listed for safety
- Belled end
The 1-1/2 in. EMT 1-Hole Straps (2-Pack) are designed to attach EMT conduit to wood, masonry or similar surfaces where good load bearing is required. Snaps positively on the conduit when installed. UL and CSA listed.
- Secures EMT conduit to surfaces
- Zinc-plated steel construction
- Corrosion resistant
- Suitable for indoor and outdoor use
Carlon PVC elbows are for use in a non-metallic PVC conduit run when directional change is necessary. Manufactured from durable PVC, the elbows are ideal for both indoor and outdoor applications. They will not rust or corrode which is especially important in outdoor applications.
- Designed for above and below-ground applications
- Use with schedule 40 rigid non-metallic conduit
- Resists rust and corrosion
- Listed for use in exposed and outdoor usage
The corrosion-resistant 1 in. EMT 90 degree Elbow changes the direction in a run of EMT conduit but still allows for easy wire pulling thanks to a large radius. Usable indoors and outdoors. This elbow meets UL and CSA requirements.
- Enables a 90 degree change of direction in a run of EMT conduit
- Corrosion-resistant galvanized steel
- Large radius allows for easy wire pulling
- UL and CSA listings
With these 3/4 - 1 in. 2-Piece Clamp Connectors (5-Pack), you can adjoin non-metallic sheathed cable to steel outlet boxes as well as other metal enclosures. For indoor use. Made of galvanized steel.
- Secures non-metallic sheathed cable to a metal enclosure such as a steel outlet box
- Made of corrosion-resistant galvanized steel
- Compatible with #10 - #14 cables
- No locknut required
The 3/4 in. Rigid or IMC Conduit Pull Elbow, with its removable cover, aids in wire pulling through a sharp bend. This elbow is made of die-cast, high-strength zinc alloy. This pull elbow meets UL and CSA requirements.
- Facilitates wire pulling through a sharp bend in a run of threaded rigid or IMC conduit
- Die-cast of high-strength zinc alloy for corrosion resistance
- UL and CSA Listed
- For indoor or outdoor applications
- Removable cover provides easy access to wiring
- Includes gasket
Small surface metal raceway systems are the ideal choice for a homeowner that wants to extend circuits or communication cabling in their home. Surface metal raceway allows you to extend circuits, add fixtures or outlets without disturbing the drywall, plaster or insulation in your home. All parts are paintable to blend with room decor. The leading choice of professionals is now available for your DIY project.
- Used as an outlet box when extending an electrical circuit from an existing switch
- Base has two 1/2 in. trade sized knockouts
- Neutral, ivory finish
- Paintable using oil based products
- UL listed
500 Series surface metal raceway system is the ideal choice for a homeowner that wants to extend a circuit to add a receptacle or light fixture in their home. Surface metal raceway allows you to add fixtures and outlets without disturbing the drywall, plaster or insulation in your home. All parts are paintable to blend with room decor. The leading choice of professionals is now available for your DIY project. Boxes, switches and fixtures.
- Carries wire from starter box to downstream outlet boxes, switches and fixtures
- 1-channel, metallic construction
- Protects power, phone or data line wiring
- ScuffCoat finish
- Paintable and stainable using latex based products
- UL listed
Use the 1 in. Rigid or IMC Conduit 1-Hole Strap when extra load bearing is needed to attach conduit to wood, masonry or a like surface. This zinc-plated strap snaps in place. Positively snaps onto the conduit.
- Secures rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required
- Zinc-plated steel resists corrosion
- UL Listed
- For indoor or outdoor applications
- Use To Cover Exposed Holes In Steel Outlet Boxes and Other Metal Enclosures
- Indoor Use Only
- 10 Per Bag
The 1/4 in. 1-Hole Ground Cable Straps (50-Pack) are handy for securing bare solid wire to a working surface. They are corrosion resistant for indoor or outdoor use. Easy installation.
- Straps secure bare wire to a wood, masonry or other work surface
- Compatible with EMT cable
- Made of corrosion-resistant galvanized steel
- Quick and easy to install
The 1 in. Non-Metallic Standard Coupling is designed for joining non-metallic conduit. It is made with PVC and is compatible with Schedule 40 and Schedule 80 RIGID non-metallic conduit (RNC). The coupling should be attached using solvent cement and is CSA and UL listed to help ensure safety.
- Designed for joining non-metallic conduit
- Compatible with schedule 40 and schedule 80 RNC
- PVC construction
- Should be attached using solvent cement
- CSA and UL listed for safety