For more than 90 years, we've been the unchallenged leader in safety switches. Our Square D brand safety switches are preferred two to one over our closest competitor. We've continued our tradition of innovation, developing new features that provide an unsurpassed level of performance, reliability, safety and ease of installation.

• QO outdoor air conditioner disconnect
• 60 Amp
• Enclosed molded case switch
• Not fusible
• Rainproof
• 240-Volt
• ANSI certified and UL listed

An air conditioning disconnect (ACD) is a disconnect located between a loadcenter (distribution panel) and air conditioner. Eaton’s ACD product line provides an installer or repair personnel with a visible disconnecting means when performing maintenance. ACDs are also known as disconnects, pullouts or air conditioning switches. The most widely used application for ACDs is for residential and light commercial air conditioning units. An ACD is installed outdoors, in visible proximity to the air conditioner condensing unit. Metallic enclosures are galvanized steel and are installed in various locations. Nonmetallic enclosures are a plastic (polycarbonate) enclosure commonly used in coastal or salt-water areas.

• ON/OFF control provided by a pullout handle
• Pullout handle can be conveniently stored in the compartment in the OFF position, helping to prevent the handle from being misplaced
• Protective shield cannot be removed until the pullout handle is removed, disconnecting the power
• Enclosure is rated NEMA 3R for outdoor use and material is galvanized steel

Siemens Talon branded products set the standard when it comes to enclosed receptacles and temporary power panels. This enclosed receptacle is ideal for use at camp grounds, with portable generators or any other outdoor application requiring a 30 Amp service. Includes a NEMA TT30R Receptacle.

• In-use rated and provided with a 30 Amp TT30R receptacle for use on 125-Volt max systems
• Ideal for use at camp grounds, portable generators or any other outdoor application requiring a 30 Amp service
• NEMA type 3R: enclosure is intended for outdoor use primarily to provide a degree of protection against falling rain and sleet and must remain undamaged by the formation or ice on the enclosure; they are not intended to provide protection against conditions such as dust, internal condensation or internal icing
• UL listed

Air conditioning disconnect is a pullout, non-fused, 2-Pole, 120/240-Volt. The enclosure is non-metallic/polycarbonate. This unit is most commonly used in coastal areas affected by rust due to moisture or salt spray.

• #2 to #14 Cu/Al wire range
• Back, bottom and side knockouts
• Interrupt rating: 10 kAIC
• Enclosure: NEMA 3R
• Amperage: 60

Siemens offers a wide variety of air conditioning disconnects. All enclosures are outdoor rated, single phase and are either 30 or 60 Amp rated. Padlocking provisions help prevent against unauthorized access. Options include steel or plastic enclosures, pull out or sliding switch disconnect, fusible or non-fused and options with GFI receptacles installed.

• 60 Amp
• Steel enclosure
• NEMA 3R enclosure per Nema/UL requirements
• 10 HP rating
• UL Listed

Siemens SN Series Load Center is the smart choice when value and quick installation are of highest priority. The SN Series load centers include labor saving features such as the ability to accept Plug-on neutral breakers, patented Insta-wire and mounting trim tabs. These exclusive features make the SN Series load center the best load center for the value minded contractor.

• Features siemens plug-on neutral, for simple quick installation, that is spacious with over 4 in. of wire bending space, and a secure reliable installation method
• SN Series plug-on neutral load center includes 1 factory installed ground bars
• Single phase load center
• Aluminum bus
• NEMA Type 1 enclosure
• Grey trim
• Interrupt rating: 100000 AIC
• UL Listed

An air conditioning disconnect (ACD) is a disconnect located between a loadcenter (distribution panel) and air conditioner. Eaton’s ACD product line provides an installer or repair personnel with a visible disconnecting means when performing maintenance. ACDs are also known as disconnects, pullouts or air conditioning switches. The most widely used application for ACDs is for residential and light commercial air conditioning units. An ACD is installed outdoors, in visible proximity to the air conditioner condensing unit. Metallic enclosures are galvanized steel and are installed in various locations. Nonmetallic enclosures are a plastic (polycarbonate) enclosure commonly used in coastal or salt-water areas.

• ON/OFF control provided by a pullout handle
• Pullout handle can be conveniently stored in the compartment in the OFF position, helping to prevent the handle from being misplaced
• Protective shield cannot be removed until the pullout handle is removed, disconnecting the power
• Enclosure is rated NEMA 3R for outdoor use and material is galvanized steel

Air conditioning disconnect is a 30 Amp fused pull-out, 2-Pole, 120/240-Volt unit. The enclosure is non-metallic/polycarbonate. This unit is most commonly used in coastal areas affected by rust due to moisture or salt spray.

• Type: fused pullout
• Amperage rating: 30 Amp
• Color: black
• Enclosure: NEMA 3R
• Enclosure material: polycarbonate
• Horsepower: 1.5 HP at 120-Volt, 3 HP at 240-Volt
• Interrupt rating: 10 kAIC
• Voltage rating: 120/240-Volt
• Wire size: #14-2 AWG Cu/Al

• Coverdome Fire Sprinkler Paint Cover
• Magnetic ring
• Protects semi-recessed fire sprinkler heads from paint
• Reduces chances of breaking the glass vial
• MFG# CDM25

Siemens offers a wide variety of air conditioning disconnects. All enclosures are outdoor rated, single phase and are either 30 Amp or 60 Amp rated. Padlocking provisions help prevent against unauthorized access. Options include steel or plastic enclosures, pull out or sliding switch disconnect, fusible or non-fused and options with GFI receptacles installed.

• 60 Amp fusible AC disconnect
• Power rating 10 HP
• Single phase 120/240-Volt rated
• Enclosure material: galvanized steel
• NEMA type 3R: enclosure is intended for outdoor use primarily to provide a degree of protection against falling rain and sleet and must remain undamaged by the formation or ice on the enclosure; they are not intended to provide protection against conditions such as dust, internal condensation or internal icing

An air conditioning disconnect (ACD) is a disconnect located between a loadcenter (distribution panel) and air conditioner. Eaton's ACD product line provides an installer or repair personnel with a visible disconnecting means when performing maintenance. ACDs are also known as disconnects, pullouts or air conditioning switches.The most widely used application for ACDs is for residential and light commercial air conditioning units. An ACD is installed outdoors, in visible proximity to the air conditioner condensing unit. Metallic enclosures are galvanized steel and are installed in various locations. Nonmetallic enclosures are a plastic (polycarbonate) enclosure commonly used in coastal or salt-water areas.

• ON/OFF control provided by a pullout handle
• Pullout handle can be conveniently stored in the compartment in the OFF position, helping to prevent the handle from being misplaced
• Protective shield cannot be removed until the pullout handle is removed, disconnecting the power
• Enclosure is rated NEMA 3R for outdoor use and material is galvanized steel