Heating Equipment Accessories
Easy to install and operate, this Com-Pak Series single-pole thermostat provides built-in temperature control. Designed exclusively for Com-Pak Series heaters, this thermostat lets you easily control the temperature with an adjustable dial. Designed with a low position (dial turned completely counterclockwise) that turns the heater on in cold rooms automatically.
- Provides built-in temperature control on Com-Pak heaters, eliminating the need for a wall thermostat and additional wiring
- Compatible with Com-Pak (CS), Com-Pak Twin (CST) and Com-Pak Max (CM) fan-forced electric heaters
- Simple 2-wire installation (single-pole)
- Almond knob matches your Com-Pak heater (White color available)
- 22 Amp
- Temperature range is 40°F - 85°F
- Accessory to UL listing of Cadet Com-Pak heaters
- 1-year limited warranty
- Choose the right thermostat for your heater and your home.
Oil Electronic Aquastat Controller provides electronic temperature sensing in a UL limit-rated controller. Controls the circulator, oil burner and boiler temperature. Provides status, LED diagnostic and EnviroCOM communication.
- Well mount, horizontal or vertical position, or flush mounted remote from the well
- Easy installation improved terminal layout and multiple knockouts make change-outs a snap
- Increased flexibility - vertical, horizontal and flush-mount options; configurable for single-function use
- Multi-function display - get set point, temperature reading and diagnostic information at your fingertips
Freshen the appearance of your Com-Pak heater with this convenient replacement grille kit. Perfect for quickly updating an old, discolored heater grille, this handy kit includes screws, a built-in thermostat knob and a plug for heaters without a thermostat. Simply installs with a screwdriver.
- Compatible exclusively with Cadet Com-Pak (CS) and Com-Pak Max (CM) electric heaters
- Use with Com-Pak and Com-Pak Max electric heaters with and without a built-in thermostat
- Kit includes screws, a built-in thermostat knob for heaters with a built-in thermostat and a plug for heaters without a thermostat
- One piece, 20-gauge steel construction with white powder-coated paint finish that eliminates sharp edges
- Installs easily using only a screwdriver
- Single grille kit in white (10-pack kits available)
- 1-year limited warranty
This is a genuine GOODMAN replacement part. Equipment should be sized, selected and installed by a qualified professional to ensure proper installation, safe operation, adherence to federal, state and local codes and for valid warranty. See installation guide for more details. Professional installation recommended.
- Direct vent side wall vent kit
- HVAC application
- Dimensions: 7 in. x 7 in. x 4.5 in.
- Kit, vent, furnace, side wall
This powerful fan-forced electric heater provides excellent warm air flow, quickly warming up to 200 sq. ft. The horizontal, register-style grille blends seamlessly into any room decor. This product is an interior replacement heater assembly only with multi-watt and multi-volt options. A full heater unit requires a wall can and grille sold separately. A line voltage wall or built-in thermostat is needed for control.
- Requires 240-Volt or 208-Volt wiring (double breaker). Before you purchase, confirm your power supply voltage (check your breaker, use a voltmeter, or refer to your old heater's label if replacing)
- Multi-Watt options with 240-Volt wiring: 1,600-Watt output (6.7 Amps, 5,460 BTUs); 900-Watt output (3.8 Amps, 3,075 BTUs); 700-Watt output (2.9 Amps, 2,390 BTUs)
- Multi-Watt options with 208-Volt wiring: 1,200-Watt output (5.8 Amps, 4,095 BTUs); 675-Watt output (3.3 Amps, 2,305 BTUs); 525-Watt output (2.5 Amps, 1,795 BTUs)
- Choose the correct heater size for your space. Simply match your area to the corresponding wattage (see chart below)
- Effectively warms small to medium sized rooms. Wire the wattage output to suit your area requirements
- Fast and simple installation with one-screw mounting into existing recessed wall can
- For complete heater, a Cadet Register wall can and grille are required (sold separately)
- Thermostat required for operation; choose a line voltage electronic or programmable wall thermostat or RMT2 built-in thermostat kit (sold separately)
- Heating element and blower made from heavy duty gauge steel
- A high-temperature safety device switches heater off if normal operating temperatures are exceeded
- UL listed in the US for safety compliance with a 5-year limited warranty
Williams offers some great solutions to make your equipment more practical and easier to use. This Digital Wall Thermostat is designed to be used with all Monterey, Direct-Vent Gravity and Console Hearth Heaters. Easy-to-read LCD screen.
- Wired thermostat or manual on/set/off
- Wall-mounted installation
- Displays room temperature in Fahrenheit or Celsius
- Battery operated
Installation Kit for 40 ft. Tube Heaters. Heatstar low-intensity infrared tube heaters direct line-of-site radiant heat to floor-level objects, which in turn, heats surrounding air to desired temperature. Personnel and objects at floor-level enjoy instant, cost-saving comfort.
- For us with the Heatstar ERXL 100,000 BTU or 125,000 BTU burner boxes with 40 ft. tube sets
- Kit includes: thermostat, shut-off valve, flex gas connector, and chain kits
- 24-Volt thermostat with 50-90 degree range
- Chain kit has 2 ft. - 3 ft. chains and 4 S-hooks per every 10 ft. of tube
This 12 in. tube extension is compatible with Williams Direct Vent Furnaces. To meet your installation needs, all models accommodate optional through the-wall vent which may extend up to a 24 in. maximum. Heavy duty metal for long life.
- Galvanized metal
- Allows for differences in heights
- For direct vent heater installations
- Replacement or new installation
Heater Element
- 120V
- 90W
- For Gas Furnace Applications (pilots, flame sensors, etc.)
The Williams Furnace Co. LP Gas Conversion Kit for the Williams Natural Gas Furnace Model #1403622 includes instructions, a conversion certificate and labels. The kit contains the necessary components for converting the Williams Natural Gas Furnace (model #1403622) to propane gas.
- Conversion kit
- Contains the necessary components for converting the Williams natural gas furnace (model #1403622) to propane gas
- Includes easy-to-follow instructions
- Includes conversion certificate and labels
The Williams Vent Limit Switch for Williams Furnaces has gold-plated switch contacts. It senses the furnace vent temperature and shuts off the appliance if it is not venting correctly. This is an important safety device for your wall heater.
- Vent limit switch, which is also referred to as a fan limit switch and is typically shaped like a small metal disc, prevents damage to your furnace by shutting the furnace down in the event that it overheats, this prevents the heat exchanger from warping and cracking from temperatures that are too high
- Compatible with Williams furnace models: 3508331, 3508332, 3508731, 3508732, 5008731, 5008732, 5508331, 5508332, 6508731, 6508732
- Board-mounted design with switch mounted on the extension straps
- Original factory part
This Williams Blower Accessory promotes increased warm air circulation and minimized temperature differences in the room for enhanced comfort. Designed to fit a variety of Williams furnaces. This blower accessory features an automatic power switch as well as a power cord for added convenience and ease of use.
- Helps improve warm air circulation and reduces temperature differences in the room for comfort
- Mounts easily inside the furnace casing
- Fits Williams model numbers 2203621, 2203622, 3003621 and 3003622
- Includes an automatic fan switch and a power supply cord (115-Volt power supply required) for your convenience
- Moves air at up to 135 CFM for effective use
Williams Blower Accessory promotes increased warm air circulation and minimized temperature differences in the room for enhanced comfort. Ideal for larger rooms where faster heat is desired. Designed to fit a variety of Hearth heaters.
- Fits model size 3501522, 5001522, 6501522, 3502522, 5002522 and 6502522
- Includes an automatic and manual fan switch along with a power supply cord
- 120-Volt
- 150 CFM
- Not for use on the 20,000 BTU/hour heaters
MFG Part# B1037485S
- Genuine OEM product
- Multiple applications (such as drain pans or anything driven by a size or dimension)
- For Gas Furnace Applications (pilots, flame sensors, etc.)
Williams Blower Accessory promotes increased warm air circulation and minimized temperature differences in the room for enhanced comfort. Designed to fit Williams Direct-Vent Furnaces 14,000 BTU. The blower accessory features a fully automatic fan switch.
- 115-Volt power supply required
- 125 CFM
- Fits direct-vent furnace 14,000 BTU models
- Blower is easy to install
Installation Kit for 40 ft. Tube Heaters. Heatstar low-intensity infrared tube heaters direct line-of-site radiant heat to floor-level objects, which in turn, heats surrounding air to desired temperature. Personnel and objects at floor-level enjoy instant, cost-saving comfort.
- For us with the Heatstar ER2STG 80,000 - 125,000 BTU burner boxes with 40 ft. tube sets
- Kit includes: thermostat, shut-off valve, flex gas connector, vent cap, and chain kits
- 24-Volt digital thermostat with 45-90 degree range
- Chain kit has 2 ft. - 3 ft. chains and 4 S-hooks per every 10 ft. of tube
Williams blower accessory for Monterey top vent furnaces improves the circulation of warm air and reduces temperature differences in the room. It features a grille that is painted soft white to match the furnace casing. This blower is an accessory add-on, this is not a standard feature of the furnace.
- Improves the circulation of warm air and reduces temperature differences in the room
- Designed for use with Monterey top-vent furnace models: 2509621, 2509622, 3509621, 3509622, 5009621 and 5009622
- Grille painted soft white to match the furnace casing
- Attaches to top of Monterey furnaces with on/off switch or automatic operation
- 115-Volt
Heater Element
- 9.6kw
- Multiple applications (such as drain pans or anything driven by a size or dimension)
- For Gas Furnace Applications (pilots, flame sensors, etc.)
480v
- 22" Leads
- 7" Diameter
- 70w
Free Standing Accessory kit allows single-sided furnaces to be surface mounted instead of recessed. Ideal for remodeling in existing masonry wall construction or when wall studs are substandard. Comes in soft-white finish, 102 in. is maximum height.
- Use with Monterey top-vent models
- Heavy-gauge metal
- Matches the texture and color of the furnace to provide a completed finish
- Includes side rails and vent cover
Installation Kit for 60 ft. Tube Heaters. Heatstar low-intensity infrared tube heaters direct line-of-site radiant heat to floor-level objects, which in turn, heats surrounding air to desired temperature. Personnel and objects at floor-level enjoy instant, cost-saving comfort.
- For us with the Heatstar ER2STG 125,000 - 175,000 BTU burner boxes with 60 ft. tube sets
- Kit includes: thermostat, shut-off valve, flex gas connector, vent cap, and chain kits
- 24-Volt digital thermostat with 45-90 degree range
- Chain kit has 2 ft. - 3 ft. chains and 4 S-hooks per every 10 ft. of tube
Installation Kit for 50 ft. Tube Heaters. Heatstar low-intensity infrared tube heaters direct line-of-site radiant heat to floor-level objects, which in turn, heats surrounding air to desired temperature. Personnel and objects at floor-level enjoy instant, cost-saving comfort.
- For us with the Heatstar ERXL 125,000 BTU, 150,000 BTU, or 175,000 BTU burner boxes with 50 ft. tube sets
- Kit includes: thermostat, shut-off valve, flex gas connector, and chain kits
- 24-Volt thermostat with 50-90 degree range
- Chain kit has 2 ft. - 3 ft. chains and 4 S-hooks per every 10 ft. of tube
The high-altitude kit for the Williams 3501521A room heater contains the necessary orifices for converting this room heater to function in elevations up to 1000 ft. Room heaters come rated for 0 to 2,000 ft. This kit will allow you to change the orifices for safe functioning at higher altitudes.
- Contains the necessary components required for converting a standard room heater to work in elevations that are between 2000 ft. and 8000 ft.
- Designed for use with the Williams gas wall heater
- Easy-to-follow instructions
- 3-orifice sizes included
The high-altitude kit for the Williams 5008232 gas wall heater contains the necessary orifices for converting this room heater to function in elevations up to 1000 ft. Standard wall heaters come rated for 0 to 2,000 ft. This kit will allow you to change the orifices for safe functioning at higher altitudes.
- Contains the necessary components required for converting a standard room heater to work in elevations that are between 2000 ft. and 8000 ft.
- Designed for use with the Williams gas wall heater
- Easy-to-follow instructions
- 3-orifice sizes included