Searched for "40140000"
Engineered for reliability, The Taco Heat Motor Power Head provides a time proven method for operation of hydronic zone valves. The exclusive heat motor design operates silently, while the twist off head allows for serviceability without disturbing system connections. This power head is 24 VAC powered with an isolated end switch.
- Isolated end switch
- 24 VAC powered
- For Taco series 570 zone valves (570, 571, 572, and 573)
- Allows for service of valve without removing it
The 005-050RP Cartridge Assembly is used on several models of Taco circulators. This kit takes the place of conventional seal kits and is extremely easy to install. The Cartridge comes with all the hardware needed to extend your Taco Circulator's operating life.
- Repair part
- Includes casing body bolts
- Easy to install
- 3-year warranty
3-5/32" Centers
- Fits B&G Series 100B,PRAB,NBF-22,NBF-12,NBF-36,PL-36B,PL-55B and Armstrong Astro 30 and S-25 Pumps
- High-quality bronze body enables long-term use
- Features 150 maximum PSI
- Comes with 2 flanges
- Works well with Armstrong Astro 30 and S-25 pumps, Bell & Gossett series 100B, PRAB, NBF-22, NBF-12, NBF-36, PL-36B, and PL-55B models
This 1/2 in. lead free anti-siphon hot or cold water vacuum breaker prevents the reverse flow of polluted water from entering into the potable water supply due to back siphonage. It consists of polished chrome plated lead free construction, chemical resistant silicone seat disc, chrome hood, and an atmospheric vent to prevent spilling. It has a full size orifice to assure pipe size capacity and maximum flow. It is ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment.
- Lead free construction
- Chrome finish
- Female NPT inlet and outlet
- Hot or cold water
- Designed to prevent the backflow of polluted water from entering into the potable water supply
- Ideal for low flow, non-continuous hot or cold water health hazard installations such as on laboratory equipment
- Maximum pressure is 125 psi
Cast Iron Construction
- Couples Motor To Pump Inside Bearing Assembly Housing
- Fits B&G Series HV Pumps & Armstrong #H-32
SuperVent, purges air through a no clog vent assembly, to control dirt and debris and minimize air vent fouling in Hydronic heating systems, while eliminating the need for bleeding. Used in Residential or Commercial closed loop hydronic heating or chilled water systems. Can be cleaned in place.
- Stainless steel concentrator which eliminates gurgling noise
- Bronze body for rigid construction
- No clog vent
- Dirt and debris resistant
- Sweat connections
- 1/2 in. connection size
- Operating temperature range (F)240 degree F maximum
- 22 Cv capacity
- Maximum safe operating pressure 125 psi
- Rugged design stands up to tough conditions and continuous service
The Taco 1 in. cast iron Freedom Flange set includes: (2) flanges, (4) nuts, and (4) mounting bolts. These flanges are designed for use with Taco "00", "00e", "2400", and "100" series hydronic circulators. Easily installed and removed with a common wrench.
- For use in a heating system
- Compatible with a wide variety of Taco circulators
- 1 in. Dia connection size
- Unique hex design provides easy-on, easy-off installation with a standard adjustable wrench
The DELAVAN 1.00 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.00 60B1 Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
High Capacity Thermostatic Radiator Valves with T104 Actuators provide control of temperature by modulating the flow of hot water or steam through free-standing radiators, convectors and other heating units with high capacity requirements. Continually monitor and adjust room temperature for consistent comfort and relief from under-heating and overheating. Designed with the higher capacity normally required by North American heating systems.
- Controller with combined remote setpoint and sensor mounted on a wall. Setpoint/sensor connect with a capillary tube to an actuator, which mounts on the valve body. For V110 valves
- Valve seat disc, which is made of resilient material (EPDM), ensures tight shutoff on steam or hot water systems
- Nickel-plated bronze casted body with working parts in cartridge insert for ease of service
- All working parts are replaceable while valve remains in service, in-line, under pressure
- Controls include sensor, set point dial and valve actuator; components may be integral or connected by capillary tubes
- Require no electrical connections
- Meet ASHRAE standard 102-1989
- 40 mm collar diameter
- Temperature Range (F) 48 degree F to 79 degree F
- Capillary Length (ft)6 ft. 8 in.
All the features you trust from the original Isolator Uni-Flange ball valve, plus a 360 degree rotating flange that allows for orientation to any degree necessary for your installation. This forged brass full port ball valve features a blow-out proof stem, adjustable packing glands and a stainless steel snap ring for extra stability during installation. The only way to isolate circulator pumps.
- Conical inlet to minimize turbulence
- Replaces 3-components, eliminates 2-leak paths, saves approximately 20 minutes in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents electrolysis
- Eliminates galvanic corrosion
The Isolator is a uni-flange ball valve that isolates a circulator pump, allowing virtually no air into the system during pump replacement or service. Its innovative design combines multiple components into a single forged brass body that saves time, labor and space. The Isolator has revolutionized the installation of circulator pumps and has evolved into the largest flanged ball valve program in the industry today, featuring patented technology with further patents pending. Designed for use with water, oil, glycol mix in residential or commercial residential plumbing, commercial plumbing, heating systems. Refer to specification sheets for additional technical information. All Webstone products are backed by a limited lifetime warranty.
- Easily Isolates the Pump for Replacement
- Replaces 8 components, eliminates 7 leak paths, saves approximately one hour in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents Electrolysis and Eliminates Galvanic Corrosion
- Rotating Flange is Secured by a Snug-Fit Snap-Ring that Provides Greater Control Over Positioning During Installation
The DELAVAN 0.50 60A1 Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.00 70B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.85 60A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.10 70B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
This non-potable water expansion tank is designed for use in commercial and residential closed loop hydronic heating system piping to control the thermal expansion of hot water and maintain system pressure below the relief setting of the relief valve. This carbon steel tank is pre-charged at 12 PSI, tank volume is 2.1 gallons and features a durable expansion membrane that prevents contact of the water with the air in the tank. This rugged butyl diaphragm minimizes loss of the air change and ensures long and trouble-free life for the system. This tank is made of carbon steel with epoxy finish, mounts to supply piping, 1/2 inch MNPT system connection and a 0.302-32 inch charging valve connection (standard tire valve) to facilitate on-site charging of the tank to meet system requirements. The maximum working pressure is 75 PSI (5.3 BAR).
- Precharged to 12 psi
- Rugged flexible butyl diaphragm
- Inline and free standing models
- Steel construction
The Armstrong SBA contain an interchangeable module that includes a stainless steel pump shaft a housing that contains a precision crafted front and back end bearings that are permanentlty lubricated. Safer solutions for Facility and service personnel. faster onsite service and replacement.
- S&H #2 Series Maintenance-free Seal Bearing Assembly with Impeller
- Universal- fits B&G 3 piece circs
- A longer circulator life without maintenance (regular oil lubrication is not required)no more oil pools on floor
- Stainless steel face plate, coupler face guard meets or exceeds OSHA standards
- The standard for 65 years in hydronics
- Repairable, replaceable, environmentally friendly and now maintenance free
The DELAVAN 0.85 70W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.50 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.10 80A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
3 Year Warranty
- System Lubricated
- Bronze Body Construction For Potable Water
- 115-volt motor ensures reliable performance
- Pump with 5.2 maximum PSI and 37 maximum GPM
- High-quality bronze body enables long-term use
- Suitable for potable water
The DELAVAN 0.75 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
I Series Combi Primary Secondary Heating Kit
- I Series Combi
- Heating Kit
- Primary Secondary
- 807000212
All the features you trust from the original Isolator Uni-Flange ball valve, plus a 360 degree rotating flange that allows for orientation to any degree necessary for your installation. This forged brass full port ball valve features a blow-out proof stem, adjustable packing glands and a stainless steel snap ring for extra stability during installation. The only way to isolate circulator pumps.
- Conical inlet to minimize turbulence
- Replaces 3-components, eliminates 2-leak paths, saves approximately 20 minutes in labor
- Fits virtually any standard circulator pump
- Available with slotted holes for high velocity pumps
- Prevents electrolysis
- Eliminates galvanic corrosion
The Armstrong ball bearing SBA contain an interchangeable module that includes a stainless steel pump shaft and a housing that contains precision crafted front and back end bearings that are permanently lubricated. Safer solution for facility and service personnel. faster on site service and replacement.
- S&H #3 Series Maintenance-free Seal Bearing Assembly without Impeller
- Universal- fits B&G 3 piece circs
- A longer circulator life without maintenance (regular oil lubrication is not required) no more oil pools on floor
- Stainless steel face plate, coupler face guard meets or exceeds OSHA standards
- The standard for 65 years in hydronics
- Repairable, replaceable, environmentally friendly and now maintenance free
The Taco 3/4 in.cast iron Freedom Flange set includes: (2) flanges, (4) nuts, and (4) mounting bolts. These flanges are designed for use with Taco "00", "00e", "2400", and "100" series hydronic circulators. Easily installed and removed with a common wrench.
- For use in a hydronic heating system
- Compatible with a wide variety of Taco circulators
- 3/4 in. Dia connection size
- Unique hex design provides easy-on, easy-off installation with a standard adjustable wrench
The "T" Style Blue Flame Log Lighter is CSA Certified. The "T" design places the unique mixing chamber in the center of the Log Lighter for connections to the center rear of the firebox. The Log Lighter pipes connect on both the left and right sides of the mixing chamber. The Blue Flame Steel Log Lighter is designed to help ignite wood in a fireplace. Eliminates the need for paper or kindling. This Log Lighter features steel construction for durability and the design of the air/gas mixing chamber makes lighting a wood fire safer than burning raw gas.
- Reduces emissions in the environment by 50% during use
- Shutter attached to the air or gas mixing chamber adjusts the flame from golden radiant to hot blue for a hotter fire
- Ignites even wet firewood
- Increases radiant heat in the room
This non-potable water expansion tank is designed for use in commercial and residential closed loop hydronic heating system piping to control the thermal expansion of hot water and maintain system pressure below the relief setting of the relief valve. This carbon steel tank is pre-charged at 12 PSI, tank volume is 4.5 gal. and features a durable expansion membrane that prevents contact of the water with the air in the tank. This rugged butyl diaphragm minimizes loss of the air change and ensures long and trouble-free life for the system. This tank is made of carbon steel with epoxy , mounts to supply piping, 1/2 in. MNPT system connection and a 0.302-32 in. charging valve connection (standard tire valve) to facilitate on-site charging of the tank to meet system requirements. The maximum working pressure is 75 PSI (5.3 BAR).
- 4.5 gal. tank
- Rugged flexible butyl diaphragm
- Inline and free standing models
- Steel construction
- Precharged to 12 PSI
- Max. Pressure 75 PSI
- Durable expansion membrane prevents contact of water with the air in the tank
- Carbon steal with epoxy
- Commercial and residential applications
- 1/2 in. MNPT system connection
The "T" Style Blue Flame Log Lighter is CSA Certified. The "T" design places the unique mixing chamber in the center of the Log Lighter for connections to the center rear of the firebox. The Log Lighter pipes connect on both the left and right sides of the mixing chamber. The Blue Flame Steel Log Lighter is designed to help ignite wood in a fireplace. Eliminates the need for paper or kindling. This Log Lighter features steel construction for durability and the design of the air/gas mixing chamber makes lighting a wood fire safer than burning raw gas.
- Reduces emissions in the environment by 50% during use
- Shutter attached to the air or gas mixing chamber adjusts the flame from golden radiant to hot blue for a hotter fire
- Ignites even wet firewood
- Increases radiant heat in the room
The DELAVAN 0.75 70W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
White Rodgers -- horizontal mounting. 50 To 90F (10 to 32C) range, 24v. 2 Stage heating, 1 stage cooling. Heat anticipator first stage 0 to 1.0 Amp, second stage . 15 To 1.0 Amp. Mercury cell switch. Energizes reversing valve in heat or cool position. Beige. Min. Order: 1 EA
Aquastat Controllers are immersion type devices for limiting or regulating the temperature of liquids in boilers, storage tanks and other applications where temperature control is required. Direct or well immersion Tradeline models include heat-conductive compound. Circulator Control and High Limit or Low Limit.
- Totally enclosed micro switch snap-acting switches operate on temperature rise to set point
- Visible control point scale and external adjustment screw permit easy setting
- Horizontal or vertical insertion of the sensing element
- Remote bulb model may be used to sense air temperature in ducts and in outside air sensing applications
- Direct or well immersion Tradeline models include heat-conductive compound
- Temperature range maximum ambient-150 degree F
- Operating temperature range 100 degree F to 240 degree F
- Differential temperature (F) 5 degree F to 30 degree F adjusted
- SPDT switching action
- Stop factory-set at 240 degree F (116 degree C); heat-conductive compound
The DELAVAN 1.25 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 1.20 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.65 80W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The Delavan .85 80A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Boiler replacement part
- For use with an oil-burning appliance
- Brass body
- Stainless-steel, hollow orifice
Character size 1/8"
- Steel dies
- Exclusive thumb grip
- Sharp characters for deep impression
- Wood box holder
- Pkg of 27
- Black
- Sharp engraved characters to ensure deep impression
- Features exclusive thumb grip for convenient handling
- Steel dies for durability and versatility
- Wooden box holder for keeping the letter stamps organized
The DELAVAN 0.65 80A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.60 60B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
2-way on-off low voltage valves consist of an actuator and valve assembly for controlling the flow of hot water. Manual opener (on all models, except straight-through, normally open valves) for valve operation on power failure; valve returns to automatic position when power is restored. All models may be installed without disassembling the valve.
- Compact construction for easy installation
- Complete powerhead may be removed or replaced without breaking plumbing line connections or draining the system
- Actuator motor may be replaced without removing the valve body or draining the system
- Electrical connections (in.) screw terminal block
- Use this valve in closed loop hydronic systems that do not contain dissolved oxygen in system water, such as fresh water from frequent source of makeup water
- Valve designed for cycling (not constantly powered on) applications
- Quick fit pushbutton powerhead makes it easy to remove for service
- Innovative motor technology offers silent operation, water hammer resist and longer life
- Series 5000 replacement powerhead is backward compatible with series 1000 zone valves
- Easy to install and operate
The DELAVAN 0.65 70W Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type W-nozzles are neither truly hollow nor solid. These nozzles frequently can be used in place of either solid or hollow cone nozzles between 0.40 and 8.00 GPH, regardless of the burners air pattern. The lower flow rates tend to be more solid. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The DELAVAN 0.65 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
The Delavan .85 80B Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type B-nozzles produce a spray that distributes droplets fairly uniformly throughout the complete pattern. The spray pattern becomes progressively hollower at higher flow rates, particularly above 8.00 GPH. Provides smooth ignition and efficient combustion, particularly in larger burners. This boiler replacement part is compatible with an oil-burning appliance.
- Boiler replacement part
- For use with an oil-burning appliance
- Brass body
- Stainless-steel, hollow orifice
The DELAVAN 1.35 70A Oil Nozzle has a stainless-steel, hollow orifice and features a brass body. Type A-nozzles are mainly used on burners with a hollow cone air pattern and for through puts up to 2.00 GPH. The droplet distribution is concentrated on the outside of the cone and results in good ignition and low-noise combustion. This boiler replacement part is compatible with an oil-burning appliance.
- Precise spray angles and optional spray uniformity through new machining process
- Reduced distributor size with shorter tangential slots to avoid plugging
- Aerodynamic body configuration
- Rolled threads to avoid metal chips and burrs
- Sintered filter for maximum protection
- Boiler replacement part is compatible with an oil-burning appliance
- ISO 9001 certified
Packard flat igniters offer an efficient , stronger, reliable hot surface silicon nitride design. These igniters are manufactured from the highest quality materials. Bacled by designs that are tried and tested to perform. Universal replacement minimizes inventory.
- Universal round silicon nitride igniter kit, includes brackets and hardware to replace hundreds of OEM furnace and boiler igniters
- Superior gas lighting ability and lower power consumption
- Faster time to temperature response and stronger more durable design
- More robust in transit