An air conditioning disconnect (ACD) is a disconnect located between a loadcenter (distribution panel) and air conditioner. Eaton's ACD product line provides an installer or repair personnel with a visible disconnecting means when performing maintenance. ACDs are also known as disconnects, pullouts or air conditioning switches.The most widely used application for ACDs is for residential and light commercial air conditioning units. An ACD is installed outdoors, in visible proximity to the air conditioner condensing unit. Metallic enclosures are galvanized steel and are installed in various locations. Nonmetallic enclosures are a plastic (polycarbonate) enclosure commonly used in coastal or salt-water areas.

• ON/OFF control provided by a pullout handle
• Pullout handle can be conveniently stored in the compartment in the OFF position, helping to prevent the handle from being misplaced
• Protective shield cannot be removed until the pullout handle is removed, disconnecting the power
• Enclosure is rated NEMA 3R for outdoor use and material is galvanized steel

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 20 Amp
• 3/4 in. single pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• (1) #14-8, (2) #14-10 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 15 Amp
• 3/4 in. single pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• (1) #14-8, (2) #14-10 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 30 Amp
• Double pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• (1) #14-8, (2) #14-10 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated

The Eaton Cutler-Hammer 20 Amp 1 in. Single-Pole Type BR Replacement Circuit Breaker is designed to protect house wires from overheating or causing a short-circuit. Single pole breaker applications include use with dishwashers, waste disposals, refrigerators, freezers, washing machines, televisions and window air conditioners. The UL-listed breaker is compatible with Westinghouse, Challenger and Bryant load centers and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 20 Amp
• Single pole 1 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #14-4 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 12/2

The Eaton 10-Terminal Grounding Bar Kit is suitable for use with type BR load centers or type CH load centers. Ground bars are required in all panels (main service panels include ground and neutral). To be sure you are selecting the correct ground bar, divide the number of circuits in the panel by 2 and pick the closest numbered ground bar. For example, a 20 circuit panel would require a GBK10P. The kit includes a 10-terminal ground bar and one 2/0 lug.

• For use as a grounding bar in a load center
• Suitable for use with type BR load centers or type CH load centers
• 10 terminals
• One 2/0 lug

Eaton provides product and service solutions for new residential construction for single-family and multi-family homes, as well as upgrades and replacements for existing homes. The Eaton Cutler-Hammer 60 Amp Double-Pole Type BR Replacement Circuit Breaker is designed to protect house wires from overheating or causing a short-circuit. Double pole breaker applications include use with spas and hot tubs. The UL-listed breaker is compatible with Westinghouse, Challenger and Bryant load centers and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 60 Amp
• Double pole 2 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #8-1/0 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 6/3

An air conditioning disconnect (ACD) is a disconnect located between a loadcenter (distribution panel) and air conditioner. Eaton’s ACD product line provides an installer or repair personnel with a visible disconnecting means when performing maintenance. ACDs are also known as disconnects, pullouts or air conditioning switches. The most widely used application for ACDs is for residential and light commercial air conditioning units. An ACD is installed outdoors, in visible proximity to the air conditioner condensing unit. Metallic enclosures are galvanized steel and are installed in various locations. Nonmetallic enclosures are a plastic (polycarbonate) enclosure commonly used in coastal or salt-water areas.

• ON/OFF control provided by a pullout handle
• Pullout handle can be conveniently stored in the compartment in the OFF position, helping to prevent the handle from being misplaced
• Protective shield cannot be removed until the pullout handle is removed, disconnecting the power
• Enclosure is rated NEMA 3R for outdoor use and material is galvanized steel

The Eaton Cutler-Hammer 30 Amp Double-Pole Type BR Replacement Circuit Breaker is designed to protect house wires from overheating or causing a short-circuit. Double pole breaker applications include use with built-in oven, range top, clothes dryer and water heater. The UL-listed breaker is compatible with Westinghouse, Challenger and Bryant load centers and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 30 Amp
• Double pole 2 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #14-4 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 10/3

The Eaton Cutler-Hammer 20 Amp 2 in. Double-Pole Type BR Replacement Circuit Breaker is UL-listed and compatible with Westinghouse, Challenger and Bryant load centers. The circuit breaker is designed for overload and short-circuit protection of your home electrical system. The breaker trips to the center position and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 20 Amp
• Double pole 2 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #14-4 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 12/3

Eaton's Type CL circuit breakers protect the wires in your home from overheating (referred to as an overload) and fault currents (referred to as short circuits). CL Breakers are classified replacement circuit breakers considered suitable, by underwriters laboratories, for use in another manufacturers load center. These breakers have been tested extensively in numerous GE, Square D and Siemens, Murray Thomas and Betts and Crouse-Hinds panels. This level of testing assures that the breakers meet identified standards and have been found suitable by UL for the specified purpose.

• Contractors can streamline inventory by carrying one manufacturer's circuit breaker versus multiple manufacturers
• CL breakers are available in 1 and 2-pole configurations
• 1-pole requires 1 in. space, 2-pole requires 2 in. space
• Trips to the off position
• Solid and stranded wire can be used together
• Classified arc fault and ground fault breakers are also available
• 15-year warranty

The Eaton Cutler-Hammer Type-BR Circuit Breaker Filler Plates allows you to cover unused spaces in a load center. This ensures that the live space is closed off. It is UL safety listed.

• Covers unused spaces in a load center
• For use with cutler-hammer type-BR load centers
• 1 in. plate for branch breaker slots
• UL listings

Our homes are filled with sensitive electronics. These devices are easily damaged by common power surges in your electrical, telephone and cable lines. It only takes a lightning storm near your home to create a high-energy electrical surge that can enter your house and destroy your appliances, TVs, stereo equipment and almost all other modern electrical products. The Eaton surge products are designed to provide protection at the point of entrance to the home. Protection at this location can reduce surges entering the home to an acceptable level for your home electronics and appliances.

• Does not protect against direct lighting strikes
• Externally mounted making it universal - compatible with any manufacturer's load center
• Product should be connected on the load side of the load center main service disconnect through a dedicated circuit breaker
• Product is recommended to use a 2-pole 50 Amp circuit breaker, sold separately
• Eaton's complete home surge protection type 2 devices (CHSPT2 Series) protect your home electronics from the damaging effects of electrical surges
• Provide premium surge protection for AC power and cable at the point of entrance to the home
• CHSPT2 family of products require a dedicated 2-pole 50 Amp thermal magnetic breaker
• Externally mounted making it universal - compatible with any manufacturer's load center or breaker box

The Eaton Cutler-Hammer 15 Amp 1 in. Single-Pole Type BR Replacement Circuit Breaker is designed to protect house wires from overheating or causing a short-circuit. Single pole breaker applications include use lighting fixtures. The UL-listed breaker is compatible with Westinghouse, Challenger and Bryant load centers and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 15 Amp
• Single pole 1 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #14-4 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 14/2

The Eaton Cutler-Hammer 60 Amp 120/240-Volt 14,400-Watt Fused Air Conditioning Disconnect is ANSI certified and CSA and UL listed. The unit has a metallic enclosure and is rated for outdoor use. The fused disconnect is compatible with class H fuses and is intended to disconnect power from an air-conditioning unit.

• Use to disconnect power from an air-conditioning unit
• NEMA 3R
• Single phase
• ON/OFF control provided by a pullout handle

Eaton's Type CL circuit breakers protect the wires in your home from overheating (referred to as an overload) and fault currents (referred to as short circuits). CL Breakers are classified replacement circuit breakers considered suitable, by underwriters laboratories, for use in another manufacturers load center. These breakers have been tested extensively in numerous GE, Square D and Siemens, Murray Thomas and Betts and Crouse-Hinds panels. This level of testing assures that the breakers meet identified standards and have been found suitable by UL for the specified purpose.

• Contractors can streamline inventory by carrying one manufacturer's circuit breaker versus multiple manufacturers
• CL breakers are available in 1 and 2-pole configurations
• 1-pole requires 1 in. space, 2-pole requires 2 in. space
• Trips to the off position
• Solid and stranded wire can be used together
• Classified arc fault and ground fault breakers are also available
• 15-year warranty

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 50 Amp
• Double pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• #10-1/0 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated

An Air Conditioning (AC) Disconnect provides an installer or repair personnel with a visible disconnecting means while performing maintenance on an air conditioning unit. The Eaton 30 Amp 120/240-Volt AC Disconnect is ANSI certified and UL listed. The unit is approved for outdoor use and features a metallic enclosure. This safety switch is designed to disconnect power from an air-conditioning unit and is rated for up to 240-Volt.

• Type: fused pullout
• Amperage rating: 30 Amp
• Color: ANSI 61 gray
• Enclosure: NEMA 3R
• Enclosure material: galvanized steel
• Horsepower: 2 HP at 120-Volt, 3 HP at 240-Volt
• Interrupt rating: 10 kAIC
• Wire size: #14-3 AWG Cu/Al
• Fuses are sold separately

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 20 Amp
• Double pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• (1) #14-8, (2) #14-10 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated

The Eaton Cutler-Hammer 50 Amp 2 in. Double-Pole Type BR Replacement Circuit Breaker trips to the center position and has a maximum load of 240-Volt. The UL-listed circuit breaker is compatible with Westinghouse, Challenger and Bryant load centers. The breaker is designed for overload and short-circuit protection of your home electrical system.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 50 Amp
• Double pole 2 in. wide breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #14-4 AWG Cu/Al at 60 degree C or 75 degree C
• Gauge/number of wires with ground - 6/3

Eaton's Type CL circuit breakers protect the wires in your home from overheating (referred to as an overload) and fault currents (referred to as short circuits). CL Breakers are classified replacement circuit breakers considered suitable, by underwriters laboratories, for use in another manufacturers load center. These breakers have been tested extensively in numerous GE, Square D and Siemens, Murray Thomas and Betts and Crouse-Hinds panels. This level of testing assures that the breakers meet identified standards and have been found suitable by UL for the specified purpose.

• Contractors can streamline inventory by carrying one manufacturer's circuit breaker versus multiple manufacturers
• CL breakers are available in 1 and 2-pole configurations
• 1-pole requires 1 in. space, 2-pole requires 2 in. space
• Trips to the off position
• Solid and stranded wire can be used together
• Classified arc fault and ground fault breakers are also available
• 15-year warranty

Eaton provides product and service solutions for new residential construction for single-family and multi-family homes, as well as upgrades and replacements for existing homes. The Eaton Cutler-Hammer 100 Amp Double-Pole Type BR Replacement Circuit Breaker is designed to protect house wires from overheating or causing a short-circuit. The UL-listed breaker is compatible with Westinghouse, Challenger and Bryant load centers and has a maximum load of 240-Volt.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 100 Amp
• Double pole breaker
• Trips to center position - must turn off then turn back on
• For use in type BR load centers
• Type BR breakers are UL approved genuine replacement breakers for load centers made by Westinghouse, Challenger and Bryant
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• Wire size - #4-2/0 AWG Cu/Al at 60 degree C or 75 degree C

Eaton's residential BR circuit breakers are used in load centers, panel boards, or similar devices. Type BR Circuit Breakers are designed to protect house wires from overheating or causing a short-circuit. Eaton's Arc Fault Circuit Interrupters (AFCIs) use advanced electronic technology to reduce fire hazards in electrical circuits and the effects of persistent arcing faults that may pose a risk of fire under certain conditions.

• Combination type includes all the protection of the branch feeder, plus it directly detects persistent low current arcing faults down to 5 Amp to efficiently protect against fire hazards in the cords connected to outlets
• FIRE-GUARD model AFCI recognizes the unique current and/or voltage signatures associated with arcing faults and efficiently interrupts the circuit to reduce fire hazards
• Branch feeder mitigates parallel arcing faults, which produce the most energy of all arcing faults, in the complete circuit including connected cords for enhanced safety
• For use in type BR load centers

Eaton has enhanced its premium Type CH residential circuit breakers, making the best even better. In addition to the industry exclusive "Trip to OFF" and simple 1-Step Reset feature, Eaton has added a trip flag to visibly indicate breaker status. Along with Tri-Drive screws and new markings that highlight ratings and the Eaton brand.

• Primary function of a circuit breaker is to protect the wire from overheating (overload) and fault currents (short circuit)
• Amperage rating: 40 Amp
• Double pole breaker
• Flag visually confirms tripped status, making it easy for the homeowner to identify
• For use in type CH load centers only
• Interrupt rating - 10 kAIC
• Voltage rating is 120/240-Volt
• #10-1/0 AWG Cu/Al 60 degree C or 75 degree C
• HACR rated